The tiling machine price in Pakistan at Punjab Tools is Rs 9,300 for the Sared SR-CT-135, a cordless tile vibrator that beds tiles evenly and cuts down on hollow spots. Around it, a tile mistri needs a way to cut (a manual tile and glass cutter or a 4-inch grinder), a 45-degree chamfer stand for mitred corners, a diamond chamfer bit for clean edges, a hole locator for drilling glazed tiles and a laser level for straight lines. The cutter, chamfer stand, chamfer bit and hole locator each cost between Rs 1,950 and Rs 2,600, and a basic laser level starts at Rs 1,350.
Tiling Machine Price in Pakistan: Sared SR-CT-135
The Sared SR-CT-135 Professional Cordless Tiling Machine (Rs 9,300) is a handheld tile vibrator with a suction pad. You stick it to the face of the tile, lift and place the tile on the bed of adhesive, then switch on the vibration. The high-frequency vibration spreads the mortar evenly under the tile and pushes out trapped air, which is what causes the hollow sound when a finished floor is tapped.
- It replaces the rubber mallet, so fewer tiles crack from heavy knocking.
- The suction pad lifts large, heavy tiles without straining your back.
- A rechargeable lithium-ion battery means no extension lead trailing across wet adhesive.
- Adjustable vibration speed suits different tile sizes and thicknesses.
- It works on wall and floor tiles in marble, ceramic and porcelain.
At Rs 9,300, the tiling machine price in Pakistan is modest next to the cost of a large-format porcelain floor, where a single cracked or hollow slab is expensive to replace.
To use it, spread adhesive with a notched trowel, place the tile, attach the machine, vibrate briefly while pressing gently, then check with a level or laser and release. Do not over-vibrate: if adhesive squeezes up through the joints, you have gone too long. On large porcelain slabs, many fixers use it together with tile leveling clips and wedges to control lippage between neighbouring tiles. Because it runs on a lithium-ion pack, keep it out of direct sun on summer sites and charge it only after it cools.
Tile Cutter Price in Pakistan: Manual Cutter, Grinder or Glass Disc
| Tool | Best for | Price |
|---|---|---|
| Professional 2-in-1 Handheld Tile & Glass Cutter Kit | Straight cuts in wall tiles, glass and mirror, roughly 3mm to 15mm thick | Rs 2,200 |
| Sared 0401 4-Inch Angle Grinder with a diamond tile disc | L-cuts, notches, thick porcelain and marble | Rs 4,800 |
| Glass Cutting Disc for Angle Grinder | Fine, low-chip cuts in glass, ceramic and porcelain | Rs 1,500 |
| Professional Angle Grinder Cutting Stand | Guided straight and angled (0 to 45°) cuts, depth up to 40mm | Rs 2,600 |
| 12V Cordless Mini Angle Grinder Kit | Trimming tiles in tight spots with 76mm discs | Rs 8,000 |
The manual cutter scores a line with a tungsten carbide wheel and then snaps the tile with a screw-pressure breaker. It is silent, dust-free and needs no electricity, which makes it ideal for straight cuts on wall tiles and mirrors. For anything that is not a straight line, or for thick vitrified and marble slabs, a 4-inch grinder is still the mistri's main cutting tool. The 1mm-thin diamond glass disc reduces chipping on glazed edges where an ordinary masonry disc leaves a rough line. For cuts around pipes and door frames, a contour gauge (Rs 2,000) copies the exact shape onto the tile.
Always cut with the guard on and wear goggles and a proper dust mask, because tile and marble dust is fine silica. Our power tool safety guide covers the rest.
Shop · 4 inch angle grinder
Sared
Sared 0401 High-Power 4-Inch Angle Grinder - 850W Heavy Duty Electric Cutter & Grinder
Sliding Angle Grinder Stand with Vise Clamp | Universal 100mm–125mm (4–5 Inch) Cut-Off Stand
Marble Chamfer Tool: 45-Degree Corners Without Plastic Trim
Outside corners on walls, steps and kitchen counters used to be finished with plastic or aluminium trim. A mitred 45-degree joint looks far cleaner, but cutting an accurate 45° edge by hand is difficult and wastes tiles.
The Professional 45-Degree Tile Chamfering Stand (Rs 2,200) holds a 4-inch (100mm) angle grinder at a fixed 45° on an aluminium alloy base with rollers, so you slide it along the tile edge and get the same angle along the whole length. Adjustment knobs set the grinder for different tile thicknesses. It suits floor and wall tiles, marble and granite.
- Mark the edge to be mitred and support the tile on a flat, stable surface.
- Fit a diamond blade suitable for tile on a 4-inch grinder and mount it in the stand.
- Set the depth so a thin strip of the glazed face remains; cutting right through to the face chips it.
- Run the stand slowly along the edge in one steady pass.
- Dry-fit both pieces at the corner before applying adhesive.
For finishing edges and holes, the Professional Diamond Chamfer Bit (Rs 1,950) is a vacuum-brazed conical bit with an M10 thread and 60/80 grit. It bevels the edge of a hole in marble, granite, porcelain or ceramic, smooths cut edges and can enlarge a pipe hole slightly. Smoothing a hole's edge removes the micro-cracks that can later spread across a tile. It works dry on site, and water extends its life. Both the Sared 0401 and the MAX 4 Inch Heavy Duty Angle Grinder have M10 spindles.
Shop · tile
Tile Hole Drilling: Using a Hole Locator
Diamond core bits have no centre pilot, so on polished porcelain, glass or marble they wander as you start and scratch the surface. The Adjustable Glass & Tile Hole Locator (Rs 2,600) solves this. A suction cup with a lock lever grips the tile, and a V-notch base with four adjustable steel roller bearings holds any core bit from 4mm to 83mm in position.
- Mark the hole centre and clean the tile so the suction cup seals.
- Lock the locator in place and set the bearings around your bit.
- Use drill mode only, because hammer action cracks tiles.
- Start at low speed with light pressure and keep the bit wet; the locator leaves room to spray water.
- Ease off as you break through, then finish the edge with the chamfer bit.
Any drill with the hammer switched off will do, and a cordless drill is the safer choice around water. For the plumbing side of pipe outlets, see our PPR and PVC plumbing tools guide.
Tile Leveling Tools: Lasers for Straight Lines
| Laser | Lines | Key details | Price |
|---|---|---|---|
| 4-in-1 Multipurpose Laser Level pro 3 | Red horizontal, vertical or cross line | Built-in 8ft tape and three bubble levels | Rs 1,350 |
| Sared SR-LL-0501 | 5 green lines (4 vertical, 1 horizontal) | Self-levels within ±3°, ±1mm at 5m, 2 batteries | Rs 13,000 |
| Sared SR-LL-1601 | 16 green lines (4D) | Two 360° horizontal and two 360° vertical lines, remote control | Rs 15,000 |
For a bathroom backsplash or a single wall, the 4-in-1 tool is enough. For full floors and rooms, a self-leveling green laser saves hours of string lines and water levels and keeps joints straight from wall to wall. Compare every option in our laser level price guide. To estimate how many tiles a room needs, the DINGQI 40M Laser Distance Meter (Rs 6,500) calculates area and volume.
Shop · laser level
Sared
Sared SR-LL-0501 5-Line Self-Leveling Green Laser Level - Professional 360° Rotary Leveling Kit
Sared
Sared SR-LL-1601 16-Line 4D Green Beam Laser Level - Professional Self-Leveling Tool with Remote Control
Mixing Adhesive and Mortar
Consistent adhesive is half the battle against hollow tiles. The Dartek PM 02-160 Paint and Mortar Mixer (Rs 12,500) has a 1200W motor, 0 to 800 RPM speed, an M14 paddle thread and a dual handle, and is built for cement, mortar, paint and tile adhesive. Mixing by shovel leaves lumps and dry pockets, while a paddle mixer gives the same consistency batch after batch.
Common Tiling Mistakes and the Tool That Fixes Them
| Problem | Usual cause | Tool that helps |
|---|---|---|
| Hollow-sounding tiles | Air pockets, uneven adhesive | Tiling machine and paddle mixer |
| Chipped cut edges | Coarse disc or a forced cut | Manual cutter or glass cutting disc |
| Cracks around pipe holes | Rough hole edges | Hole locator plus chamfer bit |
| Wandering grout lines | No reference line | Laser level |
| Gaps in corner joints | Freehand 45° cuts | 45-degree chamfering stand |
Which Tile Tools to Buy First
- Starter kit (Rs 8,350): Sared 0401 grinder (Rs 4,800), handheld tile and glass cutter (Rs 2,200) and the 4-in-1 laser level (Rs 1,350).
- Finishing upgrade (Rs 6,750): 45-degree chamfering stand (Rs 2,200), diamond chamfer bit (Rs 1,950) and hole locator (Rs 2,600).
- Contractor kit: add the Sared SR-CT-135 tiling machine (Rs 9,300) and the Sared SR-LL-0501 green laser (Rs 13,000) for large floors.
The finishing upgrade is what separates a neat job from an average one, because clean mitres and smooth pipe holes are what clients notice first. For more ways to use your grinder, see our angle grinder attachments guide.
